Steps Necessary To Pass The ACP-01101 Exam from Training Expert PassCollection
Valid Way To Pass Autodesk Certified Professional's ACP-01101 Exam
Achieving an Autodesk Certified Professional certification in AutoCAD for Drafting and Design can provide numerous benefits to professionals in the industry. It validates their skills and knowledge in using AutoCAD, a widely used software in the industry. It can also enhance their career prospects by making them more competitive in the job market and opening up opportunities for promotions and higher salaries. Additionally, it can help professionals gain recognition and credibility in the industry, which can lead to increased trust and respect from colleagues and clients.
Autodesk ACP-01101 certification exam is a professional level exam designed for individuals who wish to demonstrate their proficiency in AutoCAD for drafting and design. ACP-01101 exam is intended for professionals who work in the architecture, engineering, and construction (AEC) industries, as well as those who work in the manufacturing and product design fields.
NEW QUESTION # 14
You are setting up a drawing layout.
You need to rotate the viewport viewing angle by 90 degrees without rotating the viewport.
What should you do next?
- A. Activate the viewport that you want to rotate. Start the Dview command and use the Twist option.
- B. Select the viewport that you want to rotate, and then use the Rotate command.
- C. Activate the viewport that you want to. Start the Dview command and use the Camera option.
- D. Select the viewport that you want to rotate, and then use the UCS command with the Z Axis option.
Answer: A
Explanation:
Explanation
you need to activate the viewport that you want to rotate and start the Dview command with the Twist option.
This will allow you to rotate the view within a viewport without rotating the viewport itself.
https://knowledge.autodesk.com/support/autocad/learn-explore/caas/CloudHelp/cloudhelp/2020/ENU/AutoCAD
NEW QUESTION # 15
You have three multileaders as shown in exhibit 1. (Refer to the exhibit 1 tab.)
You need to change the display of the multileaders to match the multileaders in exhibit. (Refer to the exhibit 2 tab.)
Which command should you use?
- A. Collect Leader
- B. Align Leader
- C. Remove Leader
- D. Add Leader
Answer: A
Explanation:
Explanation
The command that you should use is B. Collect Leader1. The collect leader option groups multiple leaders into one multileader object with a common landing line1. This option is useful when you want to create a single label or callout for multiple objects2.
To use this option, you need to select the MLEADER command and then select Collect Leader from the Options menu. Then you can select two or more existing multileaders that have similar properties and press Enter. The selected multileaders will be collected into one multileader object with a common landing line1.
NEW QUESTION # 16
You place a red rectangular polyline over a PDF underlay in a drawing, and then use the rectangular polyline as a clipping boundary. The result is shown in the exhibit.
Select whether each statement is True or False.
Answer:
Explanation:
Explanation
False: You cannot create a new clipping boundary without removing the existing clipping boundary. If you want to change the clipping boundary, you have to select the PDF underlay, right-click and choose Remove Clipping Boundary first, and then use the Clip PDF command again with a different option12.
True: To access the Underlay Layers dialog box, you have to select a PDF underlay, right-click and choose PDF Layers2. In the Underlay Layers dialog box, you can click the light bulb icon for the layer name that you want to turn on or off2.
True: To use the Align command, you have to select a polyline, right-click and choose Align3. Then you have to specify two source points on the polyline and two destination points on the PDF underlay that correspond to each other3. You can also specify a third pair of points if needed3. Finally, you have to press Enter twice to confirm the alignment3. The statement "You can use the grips on the polyline to align to the edges and corners of the PDF underlay" is true. When you place a rectangular polyline over a PDF underlay and use it as a clipping boundary, the polyline's grips can be used to adjust its size and position so that it aligns with the edges and corners of the underlay.
By hovering the cursor over a grip, you can see its tooltip display the name of the grip and its function. If you then click and drag the grip, you can move it along its corresponding axis to resize the boundary. This allows you to adjust the clipping boundary to fit exactly over the content you want to display.
NEW QUESTION # 17
Refer to the exhibit.
The exhibit shows a plan view of an office arrangement. There is also a table of area of each room areas, which displays the area of each room highlighted with a bold polyline.
The room number labels in the plan are denoted by blocks; made up of a rectangle and a room number attribute.
Which entity in the drawing is used to put the graphical representation of the room number in the Room No.
column in the table?
- A. Block
- B. Rectangle and text
- C. Attribute
- D. Single line text
Answer: C
Explanation:
Explanation
a block attribute is a tag or label that attaches data to a block. The data can be extracted and displayed in a table. Therefore, the entity in the drawing that is used to put the graphical representation of the room number in the Room No. column in the table is B. Attribute.
http://autocadtip.com/how-to-create-block-attribute-in-autocad.html
NEW QUESTION # 18
Exhibit
The viewport scales in the title block shown are field value as extracted from the properties of each viewport.
When using the Insert Field command to edit the text value and generate the viewport scale, which object property should you use, if the default scale list is being used?
- A. Standard scale
- B. Visual style
- C. Display locked
- D. Object name
Answer: A
Explanation:
Explanation
The object property that you should use when using the Insert Field command to generate the viewport scale, if the default scale list is being used, is the "Standard scale".
The "Standard scale" property is used to specify the standard scale factor for the viewports. It represents a value in the format of 1:n, where n is the scale factor. For example, if you set the standard scale to 1:50, the viewport will display objects at a scale of 50 units per drawing unit.
To use this property in the Insert Field command, you can select "Object" in the "Field category" dropdown and "Standard scale" from the "Field names" dropdown. This will insert a field code that will automatically update the viewport scale based on the properties of the viewport.
NEW QUESTION # 19
Refer to the exhibit.
A workstation configuration has been created with the rectangular array command (ARRAYREST. The array is associative and has not been exploded or edited in any way. The dimensions are for reference only To adhere to current office guidelines, the walkways between the workstations need to the made wider.
Which three actions are necessary to meet office layout guidelines? (Choose three.)
- A. Change row spacing
- B. Select the appropriate array
- C. Modify column spacing
- D. Edit level spacing
- E. Replace item
Answer: A,B,C
Explanation:
Explanation
According to the search results123, a rectangular array command creates copies of objects in a regularly spaced rectangular pattern. You can adjust the spacing and number of rows and columns by dragging the grips on the array preview or modifying values on the Array context ribbon.
https://knowledge.autodesk.com/support/autocad/learn-explore/caas/CloudHelp/cloudhelp/2020/ENU/AutoCAD
NEW QUESTION # 20
What should be typed at the command line in order to start creating a line for drawing reference that starts at a defined point and extends to infinity in the designated direction?
- A. RAY
- B. XLINE
- C. CURSORSIZE
- D. MLINE
Answer: B
Explanation:
Explanation
According to the AutoCAD for Design and Drafting documents1, the command that should be typed at the command line in order to start creating a line for drawing reference that starts at a defined point and extends to infinity in the designated direction is XLINE2. This command creates a construction line, which is a type of reference line that can help you manage accurate parameters of your drawing2. You can also use point objects as nodes or reference geometry for object snaps and relative offsets3.
NEW QUESTION # 21
Select whether each statement is True or False.
Answer:
Explanation:
Explanation
True
1. According to the AutoCAD for Design and Drafting documents1, a polyline is a connected sequence of line segments created as a single object. You can create straight line segments, arc segments, or a combination of the two2341. Therefore, the correct answer is True. A polyline can include both straight line segments and arc segments.
2. False.According to the AutoCAD for Design and Drafting documents1, a spline is a smooth curve that passes through or near a set of fit points, or that is defined by the vertices in a control frame. A spline does not have a constant radius, but rather a local radius at each point on the curve2. Therefore, AutoCAD cannot directly dimension or display a radius of a spline curve23. You can use some workarounds such as exploding the curve to arc segments with the FLATTEN command2, or creating a polyline over the top with arc active3, but these may not be accurate or desirable. Therefore, the correct answer is False. The radius on a spline cannot be found in AutoCAD properties.3. TrueAccording to the AutoCAD for Design and Drafting documents1, a 2D polyline is a connected sequence of line segments created as a single object. You can specify an elevation for a 2D polyline using the Edit Polyline Elevations command2. However, this command will assign the same elevation to all vertices of the polyline2. Therefore, you cannot assign different elevations to different segments or points of a 2D polyline. Therefore, the correct answer is True. You can assign only one elevation to a 2D polyline.
NEW QUESTION # 22
You need to change the width of a specific polyline without affecting the width of the other polylines in a drawing.
What should you use?
- A. The LWEIGHT command
- B. The PLINEGEN system variable
- C. The PEDIT command
- D. The PLINEWID system variable
Answer: C
Explanation:
Explanation
polyline is a connected sequence of line segments created as a single object that can contain a width. You can change the width of a polyline by using the PEDIT command.
Based on 3 and 4, LWEIGHT is a command that sets the current lineweight, which is used for new objects and affects objects in the current space only. PLINEWID is a system variable that sets a default polyline width for new polylines. PLINEGEN is a system variable that controls how linetype patterns are generated around vertices.
https://www.roadlesstraveledstore.com/how-do-i-change-the-width-of-a-polyline-in-autocad/
https://knowledgeburrow.com/how-do-i-change-the-width-of-a-polyline-in-autocad/
NEW QUESTION # 23
What should be typed at the command line in order to start creating a line for drawing reference that starts at a defined point and extends to infinity in the designated direction?
- A. RAY
- B. XLINE
- C. CURSORSIZE
- D. MLINE
Answer: B
Explanation:
Explanation
According to the AutoCAD for Design and Drafting documents1, the command that should be typed at the command line in order to start creating a line for drawing reference that starts at a defined point and extends to infinity in the designated direction is XLINE2. This command creates a construction line, which is a type of reference line that can help you manage accurate parameters of your drawing2. You can also use point objects as nodes or reference geometry for object snaps and relative offsets3.
NEW QUESTION # 24
You have a simple polyline selected that consists of li Select whether each statement is True or False.
Answer:
Explanation:
* FalseYou cannot convert an arc to a line by hovering over the center grip of the arc segment. You need to convert the arc to a polyline first, then use the FLATTEN command, and answer YES to remove hidden lines. Then you can explode the polyline to get line segments.
https://forums.autodesk.com/t5/autocad-forum/autocad-is-it-possible-to-convert-an-arc-to-a-segemented-li
* Falseyou can edit the polyline width by hovering over certain grips if they are vertex grips or midpoint grips. However, if they are arc segment grips, you cannot edit the width by hovering over them1.
Therefore, the statement is false.
https://knowledge.autodesk.com/support/autocad/learn-explore/caas/CloudHelp/cloudhelp/2015/ENU/Auto
* Falseyou can add a new vertex by hovering over certain grips if they are edge grips or midpoint grips. However, if they are vertex grips or arc segment grips, you cannot add a new vertex by hovering over them2. Therefore, the statement is false.
NEW QUESTION # 25
You have a drawing that contains three of the same objects.
Which object has layer transparency set to 90? Click the correct object in the answer area.
Answer:
Explanation:
Explanation
According to the AutoCAD for Design and Drafting documents, layer transparency is a property that makes objects on a layer appear translucent or opaque. The higher the transparency value, the more transparent the layer appears. Therefore, the object that has layer transparency set to 90 is the one that appears the most faded or dimmed in the drawing. In this case, it is the object on the right. You can click on it to select your answer.
NEW QUESTION # 26
Drawings from different sources have been combined and resulted in duplicate background elements that are slightly offset from each other Some of the layer names match and other layers have an E prefix, indicating that they are existing.
To clean up the drawing, the Overkill (OVERKILL) command is used.
Which two settings will resolve the duplicate background and offsetting issues? (Select 2)
- A. Maintain associative objects
- B. Tolerance value
- C. Ignore Layer object property
- D. Ignore Color object property
- E. Ignore Transparency
Answer: B,C
Explanation:
Explanation
You need to ignore layer object property to remove duplicates that have different layer names but are otherwise identical4. You also need to set a tolerance value that is larger than the offset distance between the objects5.
NEW QUESTION # 27
Which two objects support associative dimensions? (Select 2)
- A. Hatches
- B. Polylines
- C. Arcs
- D. Images
Answer: B,C
Explanation:
Explanation
associative dimensions adjust to changes in the geometric objects they measure. Dimension associativity defines the relationship between geometric objects and the dimensions that give their distance and angles.
Based on 2 and 3, dimensions in a layout may be associated to objects in model space when the DIMASSOC system variable is set to 2.
NEW QUESTION # 28
You start the EXTEND command.
You need to be able to trim several objects quickly without exiting the EXTEND command.
What should you do?
- A. Hold the Ctrl+Shift key while selecting the objects.
- B. Hold the Shift key while selecting the objects.
- C. Hold the Alt key while selecting the objects.
- D. Hold the Ctrl key while selecting the objects.
Answer: B
Explanation:
Explanation
According to the AutoCAD for Design and Drafting documents1, the EXTEND command allows you to extend objects to meet the edges of other objects. To trim objects instead of extending them, you can hold down the Shift key while selecting the objects1. This will invoke the TRIM command within the EXTEND command.
https://autocadprojects.com/trim-and-extend-command/
NEW QUESTION # 29
You need to convert the two sets of parallel lines shown in 1 into the objects shown in 2 without repeating the command.
What should you use?
- A. The CHAMFER command with the Multiple option
- B. The FILLET command with the Multiple option
- C. The CHAMFER command with the Polyline option
- D. The FILLET command with the Polyline option
Answer: A
Explanation:
Explanation
According to the AutoCAD for Design and Drafting documents, the CHAMFER command creates a beveled corner between two lines, while the FILLET command creates a rounded corner between two lines. Both commands can be used with the Polyline option to apply chamfers or fillets to all corners of a 2D polyline1.
However, in this case, the lines are not polylines but separate line segments. Therefore, using the Polyline option will not work. Instead, you can use the Multiple option to chamfer or fillet multiple sets of lines without restarting the command2.
NEW QUESTION # 30
Refer to the exhibit.
You are working on a drawing. You copy a set of entities and exit the COPY command. You then use the MOVE command on the same set of entities.
Which default option should you use when prompted to select entities?
- A. Spacebar
- B. A (All)
- C. P (Previous)
- D. L (Last)
Answer: C
Explanation:
Explanation
when you use the MOVE command on a set of entities that you have previously copied, you should use B. P (Previous) as the default option when prompted to select entities. This will select the last set of entities that you modified with any command.
https://forums.autodesk.com/t5/autocad-forum/move-previous-command/td-p/3466896
https://www.cadlinecommunity.co.uk/hc/en-us/articles/360002360178-Move-Copy-Rotate-All-in-one-editing-co
NEW QUESTION # 31
......
All ACP-01101 Dumps and Autodesk Certified Professional: AutoCAD for Drafting and Design Training Courses: https://www.passcollection.com/ACP-01101_real-exams.html
Free Test Engine For Autodesk Certified Professional: AutoCAD for Drafting and Design Certification Exams: https://drive.google.com/open?id=1HZ8r2u2G8W6fGSGuScfTaLpSc8bazg85
