[Mar 07, 2022] Passing Key To Getting 352-001 Certified Exam Engine PDF
352-001 Exam Dumps Pass with Updated Mar-2022 Tests Dumps
What is the duration of the 352-001 Exam
- Number of Questions: 90-110
- Passing Score: 70%
- Format: Multiple choices, multiple answers
- Length of Examination: 120 minutes
Difficulty in writing 352-001 Exam
As all people know about this fact that Cisco 352-001 exam is not easy to pass because it requires a lot of efforts and a dependable and latest study material to efficiently pass the exam. Many Candidates have doubts in their mind before writing the Cisco 352-001 certification exam that is a pattern of the test, the types of questions asked in it and the difficulty level of the questions and time required to complete the questions. The best way to pass Cisco 352-001 exam is to challenge and improve knowledge. Candidates test their learning and identify improvement areas with the actual exam format. The best solution is to practice withCisco 352-001 Certification Practice Exam because the practice test is one of the most important elements of Cisco 352-001 exam study strategy in which Candidates can discover their strengths and weaknesses to improve time management skills and to get an idea of the score that they can expect. PassCollection offers the latest exam questions for the Cisco 352-001 Exam which can be understood by the candidates deprived of any difficulty. Our Cisco 352-001 exam dumps study material is best-suited to busy professionals who don't have much to spend on preparation and want to pass it in a week. Our Cisco 352-001 practice exam has been duly prepared by the team of experts after an in-depth analysis of Cisco recommended syllabus. We update our material regularly. So, it is intended to keep candidates updated because as and when Cisco will announce any changes in the material; we will update the material right away. After practicing with our Cisco 352-001 exam dumps Candidate can pass Cisco 352-001 exam with good grades.
The CCDE 352-001 exam is a highly coveted validation among network design engineers who want to establish their expertise in network functionalities. This qualifying test unlocks an individual’s mastery in crucial network tasks such as gathering network requirements, developing network designs, creating an implementation guide, and carrying out plans to meet the demands of a business. And if you’re successful with your exam along with its required lab evaluation, the CCDE practical exam v2.0, then you’ll be awarded the renowned Cisco Certified Design Expert (CCDE) certification. But of course, passing 352-001 test is not a piece of cake. So, we will help you accomplish your goals through the list of the relevant books & training courses below:
- CCIE and CCDE Evolving Technologies Study Guide by Brad Edgeworth, Ramiro Garza Rios, and Jason Gooley (Cisco Press)
Both the CCIE and CCDE certificates are part of the Cisco expert-level certification program. And with the changes integrated into this program, you can efficiently connect your core knowledge with the evolving technologies in the industry. These relevant advancements are thoroughly covered in this book so you thrive in whatever Cisco expert exam you pursue. Furthermore, such a study guide underlines some progressing technologies, including IoT and its architectural modes, apps, networks, and operational differences. Modern API-based automation and programmability, along with different cloud environments and cloud service models, are also addressed in the content of this manual. There’s also a section that checks on how you use structure fog and centralized compute to capitalize on the efficiency of the processes. And lastly, it helps you connect and get associated with the Cisco DevNet developer community to acquire relevant resources for Cisco network programming.
- CCDE In-Depth by Orhan Ergun (Amazon)
Carve a more effective exam journey with the aid of this high-caliber book. Featuring a rigorous elaboration of the objectives for the qualifying and practice tests, such material provides help in furnishing you with a deeper understanding of network design. It strictly follows a systematic guide so you touch on all the key technologies that are essential in today’s networking field. Some of the content covered here is network design principles, protocols, and practices. And distinctively, it does not just revolve around theoretical stuff. Thus, it highlights the real-world scenarios that network design engineers have to deal with every day. More so, it reveals the ins and outs of network design and how this area is utilized by large companies. Most of the technical tasks in such a guide are shaped into different case studies and review questions. On top of the detailed lessons, it also offers practical insights directly from the author. Through these realistic strategies straight from the expert, you will obtain more reliable techniques that will surely improve your design thinking and skills.
- CCDE Study Guide by Marwan Al-shawi (Cisco Press)
Considered as the most authoritative resource for the CCDE, this study guide incorporates both concepts and technical features of network design. It is thoroughly written and studied by the CCDE engineers who want to share the key ways to pass the tough CCDE 352-001 exam. The technologies and protocols recorded in the book are based on a variety of business requirements. This means that the content of this manual is not mainly about the fundamental technology but rather on the differences in design options. Thus, it emphasizes the variations in network designs, from its scalability to flexibility and security aspects. By understanding the dissimilarities, it’s much easier to simplify the tasks and pick the right design according to the requirements set by the company. Don’t worry because such a book delivers a lot of scenario-based samples so you can practice crafting designs and making analysis out of a given situation. Some of the related topics mentioned in this material include data centers, converged enterprise networks, service providers, high availability, QoS, multicast, IPv6, and such. In a nutshell, studying the book introduces you to a better command of network designs in various environments.
- Art of Network Architecture: Business-Driven Design by Denise Donohue and Russ White (Cisco Press)
As suggested by Cisco experts, this manual is another key item when preparing for the CCDE 352-001 validation. Uniquely, it concentrates on how businesses make use of network architecture and evolving technologies. In particular, it unravels the relationship between business requirements and technical concerns so you can optimize various network interactions in relation to people, time, and flow. Some skills developed here include customizing designs, minimizing network management pain, maximizing mobility, picking the right routing protocols, designing hardening networks, and developing data center control planes. It also gives attention to paradigm design, network topologies, network virtualization, and MPLS-based L3VPN. Moreover, the content of the book can help you in learning more about the intricacies associated with the removal and change of cloud-hosted environment, the risks associated with SDNs, and the importance of network management. All in all, the main areas highlighted in the material are cloud services, user mobility, SDN, and data center environments as these are the four design challenges that are most likely to have an effect on the business.
- Official Training Courses
It should be noted that the CCDE 352-001 exam is dubbed as a prestigious validation in the tech industry. With such standing, it’s considered as a highly challenging test that combines a lot of Cisco certification areas. As a result, it doesn’t rely on one specific course. In fact, its major sections make use of various training resources to explain the topics further. For example, the Layer 2 Control Plane subject endorses both “Implementing Cisco IP Switched Networks (SWITCH) 2.0” and “Training Course: Designing Cisco Network Service Architectures (ARCH) 3.0” courses. On the other hand, the sections in Layer 3 Control Plane about unicast routing protocol operation utilizes the “Implementing Cisco IP Routing (ROUTE) 2.0” and “Training Course: Configuring BGP on Cisco Routers (BGP) 4.0” . For the sub-area focusing on IPv6 concepts and operations, it’s suggested that you study “IPv6 Fundamentals, Design and Deployment (IP6FD) 3.0” . You can find all the recommended materials, including books, on-demand presentations, and courses from the CCDE Written Learning Matrix available on the vendor’s website.
NEW QUESTION 96
A company is planning to connect its 30 sites with a VPLS WAN backbone. A router at
each site should establish neighborships with all other routers using the OSPF routing protocol. Which three points must be considered regarding DR and BDR when different router platforms are used? (Choose three.)
- A. If the IP OSPF priority is the same for all routers, the highest loopback IP address and router ID will decide which routers will take the DR and BDR role during the selection process.
- B. To select the DR and BDR, the IP OSPF priority must be set to a lower value than the default value at the DR and BDR during the selection process.
- C. It is a best practice that the routers with the most powerful hardware should take the role of the DR and BDR.
- D. To select the DR and BDR, the IP OSPF priority must be set to a higher value than the default value at the DR and BDR during the selection process.
- E. To force two routers to become a DR and a BDR, the IP OSPF priority can be set to zero at all other OSPF routers.
- F. The role for the DR and BDR will be selected when a new OSPF router comes up.
Answer: A,C,E
NEW QUESTION 97
Which option is a fate-sharing characteristic in regards to network design?
- A. It acts as a stateful forwarding device
- B. A failure of a single element causes the entire service to fail
- C. It protects the network against failures in the distribution layer
- D. It provides data sequencing and acknowledgment mechanisms
Answer: B
NEW QUESTION 98
Which two descriptions of the transport protocols used by RESTCONF and NETCONF are true? (Choose two)
- A. NETCONF uses HTTP as Us transport protocol
- B. NETCONF uses SSH as its transport protocol
- C. RESTCONF uses gRPC as its transport protocol.
- D. RESTCONF uses SSH as its transport protocol
- E. RESTCONF uses HTTP as its transport protocol
- F. NETCONF uses gRPC as its transport protocol
Answer: B,E
NEW QUESTION 99
An MPLS service provider is offering a standard EoMPLS-based VPLS service to
Customer A, providing Layer 2 connectivity between a central site and approximately 100 remote sites. Customer A wants to use the VPLS network to carry its internal multicast video feeds, which are sourced at the central site and consist of 20 groups at 5 Mb/s each.
Which service provider recommendation is the most scalable?
- A. Use GRE tunnels to carry the streams between sites.
- B. EoMPLS-based VPLS already carries multicast traffic in a scalable manner.
- C. Replace VPLS with a Layer 3 MVPN solution to carry the streams between sites.
- D. Replicate the multicast traffic on the P routers.
Answer: C
NEW QUESTION 100
You are using iSCSI to transfer files between a 10 Gigabit Ethernet storage system and a 1 Gigabit Ethernet server. The performance is only approximately 700 Mb/s and output drops are occurring on the server switch port. Which action will improve performance in a cost-effective manner?
- A. Use a WRED random drop policy.
- B. Enable the TCP Nagle algorithm on the receiver.
- C. Change the protocol to CIFS.
- D. Increase the queue to at least 1 GB.
Answer: A
NEW QUESTION 101
What is the definition of the ITIL framework?
- A. a series of tools for process improvement that uses statistical methods to reduce defects in processes and manufacturing
- B. a five-volume framework for service management that covers design, transition, and delivery of service, and from which the ISO 20000 was developed
- C. a framework for enterprise architecture that provides a comprehensive approach for designing, planning, implementing, and governing an enterprise information architecture
- D. a framework for enterprise IP Address Management (IPAM) based on the IANA trusted
IP lease allocation scheme - E. an ISO framework that establishes a model for network management and contains guidelines for managing objects, the management database, and the application entity
Answer: B
NEW QUESTION 102
You are the Cisco Network Designer in P4S. Which two
settings must be configured in order to use the GUI to configure Call Admission Control with voice applications? (Choose two.)
- A. QoS must be set to Silver
- B. WMM must be enabled
- C. QoS must be set to Platinum
- D. QoS must be set to Gold
Answer: B,C
Explanation:
Section: (none)
Explanation/Reference:
NEW QUESTION 103
Refer to the exhibit.
This enterprise customer wants to stream one-way video from their head office to eight branch offices using multicast. Their current service provider provides a Layer 3VPN solution and manages the CE routers, but they do not currently multicast. Which solution quickly allows this multicast traffic to go through while allowing for future scalability?
- A. Implement hub and spoke MPLS VPN over DMVPN(also known as 2547oDMVPN) between CE1 and CE2
- B. Enable a GRE tunnel between nodes C1 and C4
- C. Enable a GRE tunnel between nodes C2 and C4
- D. Enable a GRE tunnel between nodes CE1 and CE2
- E. The service provider must provide a Draft Rosen Solution to enable a GRE tunnel node PE1 and PE2
Answer: D
NEW QUESTION 104
Refer to the exhibit.
23
You are developing a migration plan to enable IPv6 in your IPv4 network. Starting at R3 and assuming default IS-IS operations, what is likely to happen when you enable IPv6 routing on the link from R3 to R2?
- A. R3 advertises the link from R3-R2 to R1, R4 and R5 only.
- B. Loopback reachability between all routers for IPv4 is lost.
- C. R2 receives an IPv6 default route from R3.
- D. Only R3 and R2 have IPv4 and IPv6 reachability.
- E. All routers except R2 are reachable through IPv4.
Answer: B
Explanation:
Explanation/Reference:
Explanation:
NEW QUESTION 105
Refer to the exhibit.You are designing a loop-free hierarchical VPLS service. Which two design considerations should be implemented for the pseudowires between the N-PE and U-PE routers? (Choose two.)
- A. Enable split horizon toward the U-PE router.
- B. Disable split horizon toward the N-PE routers.
- C. Disable MAC learning on the N-PE routers.
- D. Enable split horizon toward the N-PE routers.
- E. Disable MAC learning on the U-PE route.
- F. Disable split horizon toward the U-PE router.
Answer: D,F
NEW QUESTION 106
Company Y is a mobile backhaul provider that uses microwave rings in their network. Which low-cost, simple technology do you recommend to Company Y to ensure the fastest convergence times in a ring topology?
- A. MPLS Traffic Engineering
- B. hub and spoke with ECMP
- C. sub-second IGP hello and dead timers
- D. Remote Loop-Free Alternate
- E. IP Event Dampening
Answer: D
NEW QUESTION 107
- A. via CE A
- B. via CE Aand CE B
- C. via CE B
- D. no WAN routes will be accessible
- E. During this event, how will the routes learned from the WAN be seen on the core devices?
Answer: C
Explanation:
Section: Layer 3 ControlPlane
Explanation/Reference:
NEW QUESTION 108
Which solution suppress the effect of excessive interface flapping events on routing protocols?
- A. SPF Backoff
- B. IP Event Dampening
- C. Carrier Delay
- D. BFD
Answer: B
NEW QUESTION 109
After the recent implementation of a new design that incorporated GRE tunnels into the network, the network operations staff is seeing the following syslog message in multiple routers on the network - %TUN-5-
RECURDOWN: Tunnel0 temporarily disabled due to recursive routing. From a design perspective, what was not taken into account prior to implementing the solution?
- A. The interface on the neighboring router that is the source of the tunnel is down.
- B. The neighboring routers cannot respond within the specified hold time.
- C. The router is learning the route to the tunnel destination address using the tunnel interface.
- D. The tunnel interface on the router is not receiving any keepalives within the specified hold time.
- E. The interface on the router that is the source of the tunnel is down.
Answer: C
NEW QUESTION 110
Which two factors can significantly affect the OSPF network convergence time? (Choose two.)
- A. the diameter of the OSPF network
- B. the number of OSPF routes
- C. the tuning of OSPF LSA timers
- D. different processor capabilities of devices
Answer: C,D
NEW QUESTION 111
Refer to the exhibit.
Acme Corporation hired you as a network designer to upgrade their network so that it supports IPv4 and IPv6 multicast. Which two protocols are needed on the LAN switch? (Choose two.)
- A. PIM sparse mode
- B. MLD snooping
- C. IGMP snooping
- D. Source Specific Multicast
- E. PIM snooping
Answer: B,C
NEW QUESTION 112
VPLS is implemented in a Layer 2 network with 2000 VLANs. Which must be the primary concern to ensure successful deployment of VPLS?
- A. VLAN scalability
- B. Flooding is necessary to propagate MAC address reachability information
- C. The underlying transport mechanism
- D. PE scalability
Answer: B
Explanation:
Explanation: [ I think B not 100% sure]
NEW QUESTION 113
......
352-001 exam questions for practice in 2022 Updated 270 Questions: https://www.passcollection.com/352-001_real-exams.html
