Latest Jan 14, 2022 NS0-516 Brain Dump: A Study Guide with Tips & Tricks for passing Exam
NS0-516 Question Bank: Free PDF Download Recently Updated Questions
NetApp NS0-516 Exam Topics:
| Section | Objectives |
|---|---|
| Protection | -Describe how Data Assurance with media scan protects your data. - Describe SANtricity data protection features. |
| Management | -Describe the administrative tasks for managing E-Series systems with SANtricity System Manager. -Describe the management security features in SANtricity System Manager and SANtricity Unified Manager. -Describe when and how to configure and use SANtricity Unified Manager. |
| Toolbox | -Describe the tools required to design and implement an E-Series solution. |
| Host Side | -Describe the different host connection options for E-Series systems. -Describe how to configure hosts for multipathing. |
| Troubleshooting | -Demonstrate the steps for troubleshooting an E-Series system. -Demonstrate how to analyze multipathing issues between a host and an E-Series system. |
| Documentation | -Describe the process of reviewing and preparing a site for implementation of E-Series. -Describe the information you give a customer after deploying a solution. |
| Hardware | -Describe the hardware components in an E-Series storage system. -Describe Fibre Channel, Ethernet, Infiniband and SAS cabling. -Describe the appropriate tasks for adding additional storage to an E-Series system. -Describe drive encryption features. |
| SAN | -Describe the end-to-end network configuration for Fibre Channel and Ethernet. |
| Storage Configuration | -Describe how to setup alerting and notification for the E-Series system. -Describe how to create and administer Volume Groups or DDP and associated volumes. -Describe physical and logical storage requirements. -Describe the setup of CHAP for an iSCSI environment. -Describe when to use DDP or Volume Groups. |
NEW QUESTION 79
What are two methods for setting the host protocol configuration on the E2800 controller with a 4-port 16Gbps FC or 10Gbps iSCSI SFP+ host interface card (HIC)? (Choose two)
- A. Change the QSFP type in the HIC
- B. Set in the hardware tab using SANtricity System Manager
- C. Set at the factory based on the order.
- D. Change the feature pack in the SANtricity System Manager.
Answer: A,D
NEW QUESTION 80
What is the maximum number of FC host interface cards used per NetApp EF600 storage array?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
NEW QUESTION 81
The interval for an asynchronous mirror group should usually be equal to ______________. (Choose the best answer.)
- A. the amount of time required to copy the size of the mirror repository to the remote site
- B. the corresponding application's RPO
- C. half the corresponding application's RTO
- D. the corresponding application's RTO
- E. half the corresponding application's RPO
Answer: A
NEW QUESTION 82
Which data protection strategy has the most overhead capacity as a percentage of the total capacity?
- A. RAID 10
- B. RAID 6
- C. Dynamic Disk Pools (DDP)
- D. RAID 5
Answer: D
NEW QUESTION 83
Which two steps are required to enable multifactor authentication on an E-Series system? (Choose two)
- A. Map roles
- B. Configure LDAP
- C. Test SSO login
- D. Configure In-Band Management
Answer: A,B
NEW QUESTION 84
A company wants the most scalable host-side connection topology for E-Series systems. In this scenario, which FC topology would satisfy the requirement?
- A. direct connect
- B. fabric attach
- C. private loop
- D. arbitrated loop
Answer: B
NEW QUESTION 85
Exhibit button.
Referring to the exhibit, what is the reason for the errors that are shown on port 5 on the switch of one of the fabrics?
- A. wrong switch configuration
- B. twisted cables, wrong plugs, or cable material
- C. faulty SFPs, cables, or patch panels
- D. protocol errors, encoding errors, or conversion errors
Answer: D
NEW QUESTION 86
You need to run a command from the SANtricity System Manager GUI to mark drives as native by using the CLI tool on an E-Series system that is running System Manager 11.60 or higher.
In this scenario, where would you locate this tool?
- A. Modify Existing Storage
- B. Settings -> System -> Addons
- C. Help -> CLI Command Reference
- D. Support -> Support Center -> Diagnostics
Answer: B
NEW QUESTION 87
What is the total number of ALUA paths from the host to a volume on the EF280 that is shown in the exhibit?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION 88
During normal operation, a failure was detected on an E-Series hardware component. You want to determine the location of the failed component and understand the potential recovery actions.
In this scenario, which tool would you use to accomplish this task?
- A. unreadable sectors log
- B. Host Mappings tab
- C. performance monitor
- D. Recovery Guru
Answer: D
NEW QUESTION 89
All non-I/O related activity on the storage system is recorded in the _____________. (Choose the best answer.)
- A. DACstore
- B. NVSRAM
- C. Cache backup device
- D. Event Log
- E. Storage Array Profile
Answer: A
NEW QUESTION 90
Your AutoSupport does not automatically send reports to NetApp's ActiveIQ tool.
In this scenario, how do you access the data that would have been sent using the AutoSupport feature?
- A. Access the event log by using SANtricity System Manager
- B. Use SANtricity System Manager to manually collect the support data
- C. Use SANtricity Unified Manager to collect the support data remotely
- D. Ask NetApp Support to help you to access the data by using special support tools
Answer: B
NEW QUESTION 91
Which two actions must be performed to enable iSCSI multipathing on Windows for NetApp E-Series systems? (Choose two.)
- A. Set up iSCSI IP addresses on the E-Series system and the Windows host
- B. Create two VSANs on the iSCSI switches
- C. Install the Host Utilities on the Windows host
- D. Install a Host Channel Adapter (HCA) on the Windows host
Answer: A,C
NEW QUESTION 92
Exhibit:
Which fiber cable end shown in the exhibit is supported on a NetApp E-Series system?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION 93
Review the diagram.
Is this cabling correct or incorrect, and why? (Choose the best answer.)
- A. The cabling is incorrect because it uses the top-down bottom-up cabling method
- B. The cabling is incorrect because each controller goes to only one stack of disk shelves
- C. The cabling is incorrect because the controllers are cabled from the host port.
- D. The cabling is correct for the dual stack cabling method
Answer: D
NEW QUESTION 94
What is the SANtricity Client? (Choose the best answer.)
- A. Inter-process communication that supports computer program subordinates
- B. An OS-dependent collection of utilities for servers attached to SANtricity-managed storage systems
- C. A host I/O performance modeling interface
- D. A GUI or CLI run on a host server used for storage system management
- E. A host server process that enables storage system management with the storage data path
Answer: B
NEW QUESTION 95
......
NetApp NS0-516 Exam Certification Details:
| Exam Registration | PEARSON VUE |
| Number of Questions | 60 |
| Exam Code | NS0-516 NCIE SAN Specialist E-Series |
| Passing Score | 75% |
| Exam Price | $150 USD |
| Recommended Training | E-Series Fundamentals (WBT) Configuring and Monitoring NetApp E-Series and EF-Series Storage Systems (ILT) |
| Exam Name | Implementation Engineer SAN Specialist E-Series |
| Duration | 90 minutes |
| Sample Questions | NetApp NS0-516 Sample Questions |
New NS0-516 Exam Dumps with High Passing Rate: https://www.passcollection.com/NS0-516_real-exams.html
NS0-516 Certification Exam Dumps with 180 Practice Test Questions: https://drive.google.com/open?id=1V4uvvPvXVNhvixJlml7Bl1wakE6usL8U
