100% Pass Top-selling NS0-194 Exams - New 2022 Network Appliance Pratice Exam
Network Appliance NCSE Dumps NS0-194 Exam for Full Questions - Exam Study Guide
NetApp NS0-194 Exam Certification Details:
| Exam Code | NS0-194 NCSE |
| Exam Registration | PEARSON VUE |
| Recommended Training | Introduction to NetApp Storage System Basic Components (WBT) Introduction to Clustered Data ONTAP Architecture (WBT) Introduction to Aggregates and FlexVols in Clustered Data ONTAP (WBT) Introduction to Networking in Clustered Data ONTAP (WBT) Introduction to High-Availability in Clustered Data ONTAP (WBT) Introduction to Data Protection in Clustered Data ONTAP (WBT) |
| Exam Price | $150 USD |
| Exam Name | Support Engineer |
| Number of Questions | 60 |
| Sample Questions | NetApp NS0-194 Sample Questions |
| Duration | 90 minutes |
| Passing Score | 63% |
NEW QUESTION 89
A customer is using DP SnapMirror replication between two clusters. The source cluster is using Clustered Data ONTAP 8.2.3.
Which two versions are acceptable for the destination cluster to be operating? (Choose two.)
- A. 8.3.1
- B. 8.0.2
- C. 8.1.4
- D. 8.2.3
Answer: A,D
NEW QUESTION 90
Referring to the exhibit.
The exhibit shows an overview of a customer's network design. The customer is experiencing ping loss. As part of the troubleshooting process, you receive output by using the if grp status command from the node shell.
In this scenario, what is the customer's problem?
- A. Link aggregation is not active on the switch, despite being in the design.
- B. Virtual LANs (VLANs) are not used, which causes the interfaces to be overloaded.
- C. Virtual interface (VIF) is deprecated in clustered Data ONTAP because the interface group is not working as it should.
- D. The interface group on the controller is not using the default type, causing a connection mismatch with the switch.
Answer: C
NEW QUESTION 91
You receive the error shown below on a FAS2750 HA pair.
Mon Jun 24 00:27:30 UTC [NetappA: scsi_cmdblk_strthr_admin: scsi.cmd.checkCondition:error]: Unknown device 0a.00.99: Check Condition: CDB 0x12: Sense Data SCSI:hardware error - (0x4 - 0x44 0x0 0x0) (0).
The system is cabled as shown in the exhibit.
What should you do to clear the error?
- A. Replace the controller of controller B.
- B. Replace the controller of controller A.
- C. Re-cable the system per the FAS2750 installation guide.
- D. Replace the cable connected to controller A's 0a port.
Answer: B
NEW QUESTION 92
A customer is showing disk utilization is at 100% in Active IQ even though there are low protocol operations on the controller. You review the data shown in the exhibit.
In this situation, what should you do?
- A. Reseat shelf module B.
- B. Replace disks 6b.34 and 6a.19.
- C. Add disks to the aggregate to bring down the average utilization.
- D. Replace disk 6b.39.
Answer: D
NEW QUESTION 93
A customer mentions that their Windows users cannot access clustered Data ONTAP 8.3.1 CIFS shares. The users see "access denied" on the Windows side.
Host name resolution is working and properly resolves IP to host name and host name to IP and the customer can ping using host name and IP. In this scenario, which statement describes the problem?
- A. NTP is not enabled on the clustered Data ONTAP 8.3.1 cluster.
- B. iSCSI has been enabled on the SVM.
- C. There is no proper route to the storage virtual machine (SVM) running the CIFS server.
- D. The time on the controller is skewed by more than five minutes.
Answer: A
NEW QUESTION 94
You receive the error shown below on a FAS2750 HA pair.
Mon Jun 24 00:27:30 UTC [NetappA: scsi_cmdblk_strthr_admin:
scsi.cmd.checkCondition:error]: Unknown device 0a.00.99: Check Condition: CDB
0x12: Sense Data SCSI:hardware error - (0x4 - 0x44 0x0 0x0) (0).
The system is cabled as shown in the exhibit.
What should you do to clear the error?
- A. Replace the controller of controller B.
- B. Replace the controller of controller A.
- C. Re-cable the system per the FAS2750 installation guide.
- D. Replace the cable connected to controller A's 0a port.
Answer: B
NEW QUESTION 95
A volume was accidentally deleted two hours ago by another administrator. No backups exist.
In this scenario, what do you do to restore the data?
- A. Use the volume recovery queue to restore the volume.
- B. Use a volume snapshot to return the data to the active file system.
- C. Use an aggregate snapshot to revert the aggregate to an earlier state.
- D. Use the ONTAP System Manager to recover the volume.
Answer: A
NEW QUESTION 96
A customer receives the message shown below in their EMS logs.
Tue Jun 27 18:34:18 CEST
[netapp-ct1: cp_worker: wafl.cp.toolong:error]: Aggregate AG1_NTAP_PROD experienced a long CP.
Tue Jun 27 18:37:10 CEST
Which two data sources do you use to explain this message? (Choose two.)
- A. mgwd.log
- B. Active IQ Unified Manager
- C. Performance Archive
- D. ONTAP System Manager
Answer: C,D
NEW QUESTION 97
In which three scenarios is it possible to disable and remove the aggregate Snapshot copy? (Choose three.)
- A. You are protecting volumes using SnapMirror XDP.
- B. Your cluster is part of a MetroCluster configuration.
- C. You are protecting volumes using SnapMirror DP.
- D. You are protecting the aggregate using SyncMirror.
- E. You are protecting the aggregate with RAID-DP.
Answer: A,B,D
NEW QUESTION 98
A customer will need to perform an upgrade from 9.0 to 9.4.
Which feature of ONTAP enables nondisruptive hardware maintenance for this upgrade?
- A. RAID-TEC
- B. FlexVol
- C. aggregate relocation
- D. FlexGroup
Answer: C
NEW QUESTION 99
A customer has one storage virtual machine (SVM) that is using Fibre Channel as a protocol (FCP). Some clients are successfully accessing LUNs on this SVM.
The zoning is done by using worldwide port names (WWPNs). The customer creates a second SVM for Fibre Channel and wants to access new LUNs in this SVM from the same clients.
Which three statements are true in this scenario? (Choose three.)
- A. You must map the new LUNs in the second SVM to the correct initiator group (igroup).
- B. The initiator groups (igroups) from the first SVM are also working for the second SVM.
- C. FCP must be enabled on the second SVM.
- D. Fibre Channel zoning does not need to be changed if the second SVM uses the same ports as the first SVM.
- E. Fibre Channel zoning must be reconfigured for the new SVM.
Answer: B,C,D
NEW QUESTION 100
A customer wants to upgrade a cluster to a new version of ONTAP. In this scenario, what are two ways to ensure a successful upgrade? (Choose two.)
- A. Use the Upgrade Advisor report.
- B. Use Config Advisor.
- C. Use OnCommand System Manager.
- D. Use OnCommand Unified Manager.
Answer: A,C
NEW QUESTION 101
You just replaced a controller in a single-node cluster. When the controller boots, it panics and reboots in a continuous loop.
In this scenario, which two actions are required to solve this problem? (Choose two.)
- A. Use the Special Boot Menu option to configure ADP.
- B. Use the Special Boot Menu option to clean the configuration and initialize all disks.
- C. Use the Special Boot Menu option to boot into maintenance mode.
- D. Reassign disk ownership from the old controller to the new controller.
Answer: C,D
NEW QUESTION 102
Which version of Data ONTAP would disable access to FilerView in favor of using OnCommand Manager for management?
- A. 8.1
- B. 8.2
- C. 8.0
- D. 7.3
Answer: A
NEW QUESTION 103
You are asked to replicate 15 of 20 volumes and the network configuration of your storage virtual machine to your other data center.
In this scenario, which NetApp technology should you use?
- A. SVM DR
- B. SnapMirror Synchronous
- C. SVM peering
- D. MetroCluster
Answer: B
NEW QUESTION 104
Your storage system has experienced a double-disk failure. When is this scenario considered to be in double-degraded mode?
- A. when two disks failed on a single disk shelf
- B. when two disks failed on a single aggregate
- C. when two disks failed on a node
- D. when two disks failed in a single RAID group
Answer: D
NEW QUESTION 105
......
NetApp NS0-194 Exam Topics:
| Section | Objectives |
|---|---|
| Active IQ | -Describe how to use Active IQ |
| Troubleshooting NetApp Hardware and Software | -Demonstrate knowledge of how to collect and analyze information -Demonstrate knowledge of how to troubleshoot data access problems -Demonstrate knowledge of how to analyze performance |
| NetApp Cloud Data Services | -Identify the components of cloud data services -Identify the components of a hybrid cloud solution |
| Data Protection | -Identify data protection concepts -Demonstrate knowledge of data protection operations |
| NetApp Hardware | -Identify the FRUs in a NetApp system -Demonstrate knowledge of the hardware replacement process -Describe storage hardware technology -Describe compute technology |
| ONTAP OS | -Describe disk or aggregate concepts -Describe volume concepts -Describe ONTAP networking concepts -Describe how ONTAP interacts with external components -Identify ONTAP logging mechanisms -Describe supported ONTAP protocols |
Authentic Best resources for NS0-194 Online Practice Exam: https://www.passcollection.com/NS0-194_real-exams.html
